Jinan Kelunte Bearing Co., Ltd.
Main products:Roller Bearing,Ball Bearing,Pillow Block Bearing,Import Bearing,Ceramic Bearing
Products
Contact Us
  • Contact Person : Mr. liu jolay
  • Company Name : Jinan Kelunte Bearing Co., Ltd.
  • Tel : 86-531-55509796
  • Fax : 86-531-68803368
  • Address : Shandong,jinan,No.160-31 Jiluo Road Jinan
  • Country/Region : China
  • Zip : 250031

IKO One Way Needle Roller Bearings NA4856A Exporter

IKO One Way Needle Roller Bearings NA4856A Exporter
Product Detailed
NA4856A Needle Roller Bearings 1.all types of bearings 2.Steel entity 3.High speed 4.High load carrying capacity

IKO One Way Needle Roller Bearings NA4856A Exporter

New One Way Bearing series by Jinan kelunte Bearings.Drawn cup needle roller clutches have a small radial section height and are also commonly known as One Way Bearings or Anti-Reverse Bearings. This design uses the same small radial section as drawn cup needle roller bearings which make better use of available space. The units are compact, lightweight and operate directly on a shaft; they are also suitable for transmitting high torque.

Function

Designed to transmit torque between the shaft and housing in one direction and allow free motion in the opposite direction. Proper mounting is easily accomplished with a simple press fit in the housing. Clutches and clutch and bearing assemblies are offered both in inch and metric series. One Way Bearings without bearing assemblies are indicated by suffix: HF/FC/RC. One Way Bearings with bearing assemblies are indicated by suffix: HFL/FCB/RCB.

One way bearing design Features

• Torque can be transmitted by either the housing or the shaft• Torque is positively transmitted by rollers that wedge against interior ramps• Transition from free motion to lock occurs with minimal backlash or lost motion• Available as clutch-only or as a clutch and bearing assembly• Clutch-only units should be used with external radial support to hold the shaft and housing

One way bearing applications

• Paper moving for copiers, fax machines, paper towel dispensers, etc.• Exercise equipment• Two-speed gearboxes• Rack indexing drives• Converters, non-return devices and transcendental clutches. • Fishing Reels, RC Cars, RC Helis, RC Engines

Inspection of one way bearings

Although the outer cup of the clutch is accurately drawn from strip steel, it can go slightly out of round during heat treat. When the assembly is pressed into a ring gage or properly prepared housing of correct size and wall thickness, it becomes round and properly sized. Direct measurement of the outside diameter of a drawn cup assembly is an incorrect procedure. The proper inspection procedure is as follows:

1. Press the assembly into a ring gage of the proper size as given in the tabular data.2. Gage the bore with the specified plug gages of the proper size, as given in the tables of dimensions.

- The locking plug is rotated to insure lockup when the clutch is operated at low limit shaft and is mounted in a high limit housing strong enough to properly size the clutch. - The overrun plug is rotated to ensure free over-running when the clutch is operated on a high limit shaft and is mounted in a low limit housing. - The go plug and no go plug insure proper size of the bearings in the clutch and bearing assemblies.

Installation of one way bearings

Simplicity of installation promotes additional cost savings. The drawn cup roller clutch, or the clutch and bearing assembly, must be pressed into its housing. The unit is pressed into the bore of a gear hub or pulley hub, or housing of the proper size, and no shoulders, splines, keys, screws or snap rings are required. Installation procedures are summarized in the following sketches:

Use an arbor press or hydraulic ram press which will exert steady pressure. Never use a hammer or other tool requiring pounding to drive the clutch into its housing.

Make sure that the housing bore is chamfered to permit easy introduction of the clutch and bearing or the clutch unit. Press unit slightly beyond the chamfer in the housing bore to assure full seating. Through-bored housings are always preferred. If the housing has a shoulder, never seat the clutch against the shoulder.

IMPORTANT: The mounted clutch or clutch and bearing assembly engages when the housing is rotated relative to the shaft in the direction of the arrow and LOCK marking stamped on the cup. Make sure that the unit is oriented properly before pressing it into its housing.

Use an installation tool as shown in the diagram below. If clutch is straddled by needle roller bearings, press units into position in proper sequence and preferably leave a small clearance between units. When assembling the shaft, it should be rotated in the overrun direction during insertion. The end of the shaft should have a large chamfer or rounding.

ItemOld ItemdDW(mm)CrCorGreaseoilweight
NA4836454483618022545-----
NA4838454483819024050-----
NA4840454484020025050-----
NA4844454484422027050-----
NA4848454484824030060-----
NA4852454485226032060-----
NA4856454485628035069-----
NA4860454486030038080-----
NA4864454486432040080-----
NA4868454486834042080-----
NA490045449001022137.69.131000-0.025
NA490145449011224138.611.128000-0.028
NA490245449021528139.0512.623000-0.036
NA490345449031730139.61421000-0.04
NA4904454490420371715.921.118000-0.081
NA4905454490525421718.326.915000-0.096
NA4906454490630471719.931.313000-0.11
NA4907454490735552026.94911000-0.186
NA4908454490840622232.658.59700-0.249
NA4909454490945682233.261.99000-0.294
NA4910454491050722235.670.28100-0.298
NA4911454491155802544.487.27500-0.428
NA4912454491260852545.893.36900-0.459
NA4913454491365902566.11146400-0.45

IKO One Way Needle Roller Bearings NA4856A Exporter



Copyright Notice @ 2008-2022 ECVERY Limited and/or its subsidiaries and licensors. All rights reserved.