IKO One Way Needle Roller Bearings HK1412 Wholesaler

HK1412 Needle Roller Bearings 1.all types of bearings 2.Steel entity 3.High speed,precision 4.High load carrying capacity

IKO One Way Needle Roller Bearings HK1412 Wholesaler

IKO One Way Bearing series by Jinan kelunte Bearings Company. Drawn cup needle roller clutches

have a small radial section height and are also commonly known as One Way Bearings or Anti-Reverse Bearings. This 

design uses the same small radial section as drawn cup needle roller bearings which make better use of available space. The units are compact, light weight and operate directly on a shaft; they are also suitable for transmitting high torque.

Function

Designed to transmit torque between the shaft and housing in one direction and allow free motion in the opposite direction. Proper mounting is easily accomplished with a simple press fit in the housing. Clutches and clutch and bearing assemblies are offered both in inch and metric series. One Way Bearings without bearing assemblies are indicated by suffix: HF/FC/RC. One Way Bearings with bearing assemblies are indicated by suffix: HFL/FCB/RCB.

IKO Bearings Products

IKO Deep groove ball bearings / IKO Taper roller bearings / IKO Self-aligning ball bearings /IKO Thrust ball bearings

IKO Cylindrical roller bearings / IKO Needle roller bearings / IKO Pillow block bearings

IKO bearing design Features

• Torque can be transmitted by either the housing or the shaft• Torque is positively transmitted by rollers that wedge against interior ramps• Transition from free motion to lock occurs with minimal backlash or lost motion• Available as clutch-only or as a clutch and bearing assembly• Clutch-only units should be used with external radial support to hold the shaft and housing

One way bearing applications

• Paper moving for copiers, fax machines, paper towel dispensers, etc.• Exercise equipment• Two-speed gearboxes• Rack indexing drives• Converters, non-return devices and transcendental clutches. • Fishing Reels, RC Cars, RC Helis, RC Engines

Inspection of one way bearings

Although the outer cup of the clutch is accurately drawn from strip steel, it can go slightly out of round during heat treat. When the assembly is pressed into a ring gage or properly prepared housing of correct size and wall thickness, it becomes round and properly sized. Direct measurement of the outside diameter of a drawn cup assembly is an incorrect procedure. The proper inspection procedure is as follows:

1. Press the assembly into a ring gage of the proper size as given in the tabular data.2. Gage the bore with the specified plug gages of the proper size, as given in the tables of dimensions.

- The locking plug is rotated to insure lockup when the clutch is operated at low limit shaft and is mounted in a high limit housing strong enough to properly size the clutch. - The overrun plug is rotated to ensure free over-running when the clutch is operated on a high limit shaft and is mounted in a low limit housing. - The go plug and no go plug insure proper size of the bearings in the clutch and bearing assemblies.

Installation of one way bearings

Simplicity of installation promotes additional cost savings. The drawn cup roller clutch, or the clutch and bearing assembly, must be pressed into its housing. The unit is pressed into the bore of a gear hub or pulley hub, or housing of the proper size, and no shoulders, splines, keys, screws or snap rings are required. Installation procedures are summarized in the following sketches:

Use an arbor press or hydraulic ram press which will exert steady pressure. Never use a hammer or other tool requiring pounding to drive the clutch into its housing.

Make sure that the housing bore is chamfered to permit easy introduction of the clutch and bearing or the clutch unit. Press unit slightly beyond the chamfer in the housing bore to assure full seating. Through-bored housings are always preferred. If the housing has a shoulder, never seat the clutch against the shoulder.

IMPORTANT: The mounted clutch or clutch and bearing assembly engages when the housing is rotated relative to the shaft in the direction of the arrow and LOCK marking stamped on the cup. Make sure that the unit is oriented properly before pressing it into its housing.

Use an installation tool as shown in the diagram below. If clutch is straddled by needle roller bearings, press units into position in proper sequence and preferably leave a small clearance between units. When assembling the shaft, it should be rotated in the overrun direction during insertion. The end of the shaft should have a large chamfer or rounding.

IKO HK Needle Roller Bearings Series

item	old Item	d	D	h
		(mm)	(mm)
HK0408	37941/4	4	8	8
HK0509	47941/5	5	9	9
HK0608	37941/6	6	10	8
HK0609	47941/6	6	10	9
HK0709	47941/7	7	11	9
HK0808	37941/8	8	12	8
HK0810	57941/8	8	12	10
HK0910	57941/9	9	13	10
HK0912	67941/9	9	13	12
HK1010	57941/10	10	14	10
HK1012	67941/10	10	14	12
HK1210	57941/12	12	16	10
HK1412	37941/14	14	20	12
HK1416	57941/14	14	20	16
HK1512	37941/15	15	21	12
HK1516	57941/15	15	21	16
HK1612	37941/16	16	22	12
HK1616	57941/16	16	22	16
HK1712	37941/17	17	23	12
HK1812	37941/18	18	24	12
HK1816	57941/18	18	24	16
HK2010	27941/20	20	26	10
HK2012	37941/20	20	26	12
HK2016	57941/20	20	26	16
HK2210	27941/22	22	28	10
HK2212	37941/22	22	28	12
HK2216	57941/22	22	28	16
HK2512	27941/25	25	32	12
HK2516	47941/25	25	32	16
HK2520	67941/25	25	32	20
HK2816	47941/28	28	35	16
HK2820	67941/28	28	35	20
HK3012	27941/30	30	37	12
HK3016	47941/30	30	37	16
HK3020	67941/30	30	37	20
HK3512	27941/35	35	42	12
HK3520	67941/35	35	42	20
HK4012	27941/40	40	47	12
HK4020	67941/40	40	47	20
HK4512	27941/45	45	52	12

IKO One Way Needle Roller Bearings HK1412 Wholesaler